quality control raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2026-07-06 and is reviewed periodically as new material appears.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
=== Surface plasmon resonance === The SBP-Tag has been used to reversibly immobilize recombinant proteins onto streptavidin-functionalized surfaces thereby permitting interaction assessment such as by surface plasmon resonance (SPR) techniques with re-use of the functionalized surface. SPR has also been used to compare the SBP-Tag with other streptavidin-binding peptides such as Strep-tag.
Photochemistry – study of chemical reactions that proceed with the absorption of light by atoms or molecules. Quantum chemistry – branch of chemistry whose primary focus is the application of quantum mechanics in physical models and experiments of chemical systems. Solid-state chemistry – study of the synthesis, structure, and properties of solid phase materials, particularly, but not necessarily exclusively of, non-molecular solids. Spectroscopy – study of the interaction between matter and radiated energy. Stereochemistry – study of the relative spatial arrangement of atoms that form the structure of molecules Surface science – study of physical and chemical phenomena that occur at the interface of two phases, including solid–liquid interfaces, solid–gas interfaces, solid–vacuum interfaces, and liquid-gas interfaces. Thermochemistry – the branch of chemistry that studies the relation between chemical action and the amount of heat absorbed or generated. Calorimetry – the study of heat changes in physical and chemical processes. Organic chemistry (outline) – study of the structure, properties, composition, mechanisms, and reactions of organic compounds. An organic compound is defined as any compound based on a carbon skeleton. Biochemistry – study of the chemicals, chemical reactions and chemical interactions that take place in living organisms. Biochemistry and organic chemistry are closely related, as in medicinal chemistry or neurochemistry. Biochemistry is also associated with molecular biology and genetics.
14 April – First Minister Humza Yousaf condemns Iran's attack against Israel, describing it as an "extremely worrying development. 15 April – Police Scotland make their first two arrests for alleged offences breaching the Hunting with Dogs (Scotland) Act 2023. 17 April – MSPs vote to increase the minimum alcohol price by 30% from September, when alcoholic drinks will rise from 50p to 65p per unit, with the increase in line with inflation. 18 April – Peter Murrell, the former chief executive of the Scottish National Party (SNP) and husband of Nicola Sturgeon, is re-arrested by Police Scotland and charged in connection with the embezzlement of funds from the SNP. Murrell also resigns his membership of the SNP. The Scottish Government scraps its target of achieving Net Zero by 2030, as well as annual and interim targets for reducing greenhouse gases, and instead replaces them with a system measuring emissions every five years. Following a review of gender services in England, NHS Scotland pauses the use of puberty blockers for children in Scotland, while Glasgow's Sandyford Clinic says 16- and 17-year-olds will need to wait until they are 18 to be prescribed the drugs. 19 April – At the High Court in Glasgow, Kristofer Johnstone is sentenced to ten years in prison after being convicted of the rape and abuse of two girls between 2003 and 2018. The Scottish Greens announce their intention to hold a vote on whether to stay in government with the Scottish National Party following the SNP's decision to scrap key climate targets.
The leaves of the coca plant contain alkaloids that—when extracted chemically—are the source for cocaine base. The amount of coca alkaloid in the raw leaves is small, however. A cup of coca tea prepared from one gram of coca leaves (the typical contents of a tea bag) contains approximately 4.2 mg of organic coca alkaloid. (In comparison, a typical dose (a "line") of cocaine contains between 20 and 30 milligrams.) Owing to the presence of these alkaloids, coca tea is a mild stimulant; its consumption may be compared to consumption of a moderately strong cup of coffee or tea. The coca alkaloid content of coca tea is such that the consumption of one cup of coca tea can cause a positive result on a drug test for cocaine, however. Similar to decaffeination in coffee, coca tea can be decocainized. Just as decaffeinated coffee retains a small quantity of caffeine, decocainized coca tea will still contain a small quantity of organic coca alkaloids. There is little information on the pharmacological and toxicological effects of consuming coca tea. A chemical analysis by solid-phase extraction and gas chromatography–mass spectrometry (SPE-GC/MS) of Peruvian and Bolivian tea bags indicated the presence of significant amounts of cocaine, the metabolite benzoylecgonine, ecgonine methyl ester and trans-cinnamoylcocaine in coca tea bags and coca tea. Urine specimens were also analyzed from an individual who consumed one cup of coca tea and it was determined that enough cocaine and cocaine-related metabolites were present to produce a positive drug test.
Sources: en.wikipedia.org
== History == Planet Half-Life ran from April 27, 1999 to August 13, 2012. Since then, it had undergone numerous format changes, both in content and aesthetic. The following is a timeline of major changes and other events.
== Notable researchers == Roger Guillemin and Andrew W. Schally were awarded the Nobel Prize in Physiology and Medicine in 1977 for their contributions to understanding "the peptide hormone production of the brain"; these scientists independently first isolated TRH and GnRH and then identified their structures.
== Further reading == Barnett, Michael and Finnemore, M. (2004). Rules for the World: International Organizations in Global Politics. Cornell University Press. Hurd, Ian (2018). International Organizations: Politics, Law, Practice. Cambridge University Press. Lall, Ranjit (2017). "Beyond Institutional Design: Explaining the Performance of International Organizations." International Organization 53: 699–732. Lall, Ranjit (2023). Making International Institutions Work: The Politics of Performance. Cambridge University Press. Lavelle, Kathryn C. (2020). The Challenges of Multilateralism. Yale University Press. ISBN 9780300230451. Muntschick, Johannes, ed. (2022): Regionalism in Africa and External Partners. Uneven Relationships and (Un)Intended Effects. Cham: Palgrave. doi:10.1007/978-3-031-10702-3. Claude, Inis L. Jr. (1964) [1959]. Swords into Plowshares: The problems and progress of international organization (3rd ed.). New York: Random House. OCLC 559717722. Datasets:
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
System suitability is a set of checks that confirm the instrument and method perform within limits before sample analysis. It typically includes resolution, tailing factor, retention time, and peak area reproducibility. If a check fails, the run is invalidated until the cause is resolved.