The short version of Chromatogram fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-05-24. Anything still debated is marked as such rather than presented as settled.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
=== Use and distribution === Guidelines regarding viral diagnoses and treatments change frequently and limit quality care. Even when physicians diagnose older patients with influenza, use of antiviral treatment can be low. Provider knowledge of antiviral therapies can improve patient care, especially in geriatric medicine. Furthermore, in local health departments (LHDs) with access to antivirals, guidelines may be unclear, causing delays in treatment. With time-sensitive therapies, delays could lead to lack of treatment. Overall, national guidelines, regarding infection control and management, standardize care and improve healthcare worker and patient safety. Guidelines, such as those provided by the Centers for Disease Control and Prevention (CDC) during the 2009 flu pandemic caused by the H1N1 virus, recommend, among other things, antiviral treatment regimens, clinical assessment algorithms for coordination of care, and antiviral chemoprophylaxis guidelines for exposed persons. Roles of pharmacists and pharmacies have also expanded to meet the needs of public during public health emergencies.
== Principle == This technique is applicable to gases or any materials that can be vaporized. It uses a non-fragmenting non-conventional ionisation mode, by attachment of a lithium (or alkaline) ion to the gas to be analysed with a more traditional mass filter. This instrument is more dedicated to analysis of moderately-sized molecules such as organic or aromatic compounds.
In 1968, a period of political liberalization took place in Czechoslovakia called the Prague Spring. An "Action Program" of reforms included increasing freedom of the press, freedom of speech and freedom of movement, along with an economic emphasis on consumer goods, the possibility of a multiparty government, limitations on the power of the secret police, and potential withdrawal from the Warsaw Pact. In answer to the Prague Spring, on 20 August 1968, the Soviet Army, together with most of their Warsaw Pact allies, invaded Czechoslovakia. The invasion was followed by a wave of emigration, including an estimated 70,000 Czechs and Slovaks initially fleeing, with the total eventually reaching 300,000. The invasion sparked intense protests from Yugoslavia, Romania, China, and from Western European countries.
=== Freeze drying === In planning for the long-duration Apollo missions, NASA conducted extensive research into space food. One of the techniques developed in 1938 by Nestlé was freeze drying. The foods are cooked, quickly frozen, and then slowly heated in a vacuum chamber to remove the ice crystals formed by the freezing process. The final product retains 98% of its nutrition and weighs much less than before drying. The ratio of weight before and after drying depends strongly on the particular food item but a typical freeze-dried weight is 20% of the original weight. In the United States, Action Products later commercialized this technique for other foods, concentrating on snack food resulting in products like Space ice cream. Today, one of the benefits of this advancement in food preservation includes simple, nutritious meals available to disabled and otherwise homebound senior adults unable to take advantage of existing meal programs.
The majority of tulip cultivars are classified in the taxon Tulipa gesneriana. They have usually several species in their direct background, but most have been derived from Tulipa suaveolens. Tulipa gesneriana is in itself an early hybrid of complex origin and is probably not the same taxon as was described by Conrad Gessner in the 16th century. The UK's National Collection of English florists' tulips and Dutch historic tulips, dating from the early 17th century to c. 1960, is held by Polly Nicholson at Blackland House, near Calne in Wiltshire.
Sources: en.wikipedia.org
=== Science and academia === Andy Miah, professor of science communication and future media at the University of Salford, called TEG a "provocation", saying that "... the significant risk of athletes excessively enhancing and risking significant health complications is unaddressed by their materials. There is no mention of medical oversight in the competition on the website, from what I can see." Fraser said that "Each athlete must be under clinical supervision." According to D'Souza, "We will focus on athlete safety by mandating athletes have pre-competition full-system clinical screenings including blood tests and EKGs." Science writer Ronald Bailey said, "Let fans decide which play they prefer." Grigory Rodchenkov, former head of the Moscow Anti-Doping Laboratory, said it was a "danger to health, to sport." Academic John William Devine said, "In a sporting world in which inequality of opportunity is already rampant, the removal of the doping ban would only deepen an existing moral failing." According to John Hoberman, author of several books on sports and doping, D'Souza's idea that drugs would lead to better performance is "very simplistic", and D'Souza is "very shallow on the scientific end". Anti-doping expert Michael Ashenden expressed support for the games in 2024, "provided their athletes do nothing illegal". Science philosopher Byron Hyde said that the large financial incentives offered by TEG risk coercing struggling athletes into participating, undermining their autonomy.
Macrolides Azithromycin Clarithromycin Erythromycin When taken independently, erythromycin has been shown to cause both QT prolongation and TdP. Erythromycin works inhibiting the CYP3A protein. Patients who have low CYP3A activity and are also concurrently taking other medications such as disopyramide, which can lead to QT prolongation and TdP. Fluoroquinolones Ciprofloxacin Levofloxacin Moxifloxacin
== Habitat and ecology == Rhizopus oryzae can be found in various soils across the world. For example, it has been found in India, Pakistan, New Guinea, Taiwan, Central America, Peru, Argentina, Namibia, South Africa, Iraq, Somalia, Egypt, Libya, Tunisia, Israel, Turkey, Spain, Italy, Hungary, Czech Republic, Slovakia, Germany, Ukraine, British Isles, and the USA. The soils where R. oryzae has been isolated are varied ranging from grassland, cultivated soils under lupin, corn, wheat, groundnuts, other legumes, sugar canes, rice, citrus plantations, steppe type vegetation, alkaline soils, salt-marshes, farm manure soils, to sewage filled soils. The pH of the soils where the species has been isolated typically range from 6.3 to 7.2. Rhizopus oryzae is often identified as R. arrhizus when isolated from foods. It is found in rotting fruits and vegetables where it is often called R. stolonifer. Unlike the other species such as R. stolonifer, R. oryzae is common in tropical conditions. In East Asia, it is common in peanuts. For instance, there was 21% isolation from peanut kernels from Indonesia. It is present in maize, beans, sorghum, and cowpeas, pecans, hazelnuts, pistachios, wheat, barley, potatoes, sapodillas, and various other tropical foods. Maize meal on which isolates of R. oryzae had been grown was found to be toxic to ducklings and rats, causing growth depression.
== Description == Egg cases are made of collagen protein strands, and are often described as feeling rough and leathery. Some egg cases have a fibrous material covering the outside of the egg case, thought to aid in attachment to substrate. Egg cases without a fibrous outer layer can be striated, bumpy, or smooth and glossy. With the exception of bullhead shark eggs, egg cases are typically rectangular in shape with projections, called horns, at each corner. Depending on the species, egg cases may have one or more tendrils.
== Risks and side effects == Several studies have found fat grafting of the lip to be one of the best methods of maintaining a semi-permanent fuller and softer lip. When the lips are overfilled, the results can be comic, often supplying fodder to tabloid newspapers and offbeat websites. This look is sometimes mockingly called a 'trout pout.' Overaggressive injections can lead to lumpiness while too little can result in ridges. Common reactions can range from redness, swelling or itching at the injection site(s). Other possible complications include bleeding, uneven lips, movement of the implants, or extrusion, when an implant breaks through the outermost surface of the skin. Swelling and bruising can last from several days to a week. Some patients are allergic to the common local anesthetics like lidocaine and probably should not consider lip injections. Some react badly to the skin test that patients must take before receiving collagen. Other patients who should forego procedures to the lip include those who have active skin conditions like cold sores, blood clotting problems, infections, scarring of the lips or certain diseases like diabetes or lupus that cause slower healing. Patients with facial nerve disorders, severe hypertension or recurrent herpes simplex lesions should also eschew lip augmentation. As in all surgeries, smokers complicate completion of their procedure as well as the speed of healing. Fat transfer can last longer than other injected materials but can have lumping or scarring effects.
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.