If you have been reading about retention time and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-08-19. Where a claim depends on a specific study, the study is described rather than over-claimed.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
| Property | Value | Notes |
|---|---|---|
| Accuracy | Recovery near 100% | Depends on acceptance criteria and matrix |
| Precision | Relative standard deviation | Often at or below 2% for replicate injections |
| Limit of detection | Signal-to-noise ratio 3:1 | Approximate and method-specific |
| Limit of quantitation | Signal-to-noise ratio 10:1 | Confirmed by precision and accuracy |
| Resolution | 1.5 or greater | Typical system suitability target |
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
== Advantage and limitations == Immunoliposomes have many possible applications as described above and have certain advantages in new research and ideas. Some advantages being researched include immunoliposomes targeting specific molecules in the body. In preclinical testing, they can be environmentally responsive to specific conditions of temperature, pH, enzymes, redox reactions, magnetic energy, and light to release drugs. This conditional ability allows immunoliposomes to focus on specific target areas which can be beneficial for drug delivery. Increased targeting allows the possibility for decreased systemic toxicity while increasing drug concentration at a certain site. Even with this advantage of immunoliposomes, there are some challenges in their application. The success of immunoliposomes during in vivo testing has been shown by multiple groups including Meeroekyai et al 2023 and animal testing has been successful in groups such as Refaat et al 2022. However, they struggle to thrive in higher level and clinical testing. This challenge stems from the variability and lack of understanding of tumors, pharmacokinetics, and large scale production of immunoliposomes. For example, tumors vary but typically have increased vascular permeability and decreased lymphatic drainage which lead to the EPR effect. EFR is the enhanced permeability and retention effect in which drug carriers depend on but the effect and environment can vary in solid tumors. This varying environment makes it hard to predict how the immunoliposome acts and quantify its pharmacokinetics.
Sigma is the Sigma-Aldrich's main biochemical supplier, with offerings including antibiotics, buffers, carbohydrates, enzymes, forensic tools, hematology and histology, nucleotides, proteins, peptides, amino acids and their derivatives.
==== Absorption ==== Following a single oral dose of sertraline, mean peak blood levels of sertraline occur between 4.5 and 8.4 hours. Bioavailability is likely linear and dose-proportional over a dose range of 150 to 200 mg. Concomitant intake of sertraline with food slightly increases sertraline peak levels and total exposure. There is an approximate 2-fold accumulation of sertraline with continuous administration and steady-state levels are reached within one week.
Sources: en.wikipedia.org
Masterton and Slowinski used three criteria to describe the six elements commonly recognised as metalloids: metalloids have ionization energies around 200 kcal/mol (837 kJ/mol) and electronegativity values close to 2.0. They also said that metalloids are typically semiconductors, though antimony and arsenic (semimetals from a physics perspective) have electrical conductivities approaching those of metals. Selenium and polonium are suspected as not in this scheme, while astatine's status is uncertain. In this context, Vernon proposed that a metalloid is a chemical element that, in its standard state, has (a) the electronic band structure of a semiconductor or a semimetal; and (b) an intermediate first ionization potential "(say 750−1,000 kJ/mol)"; and (c) an intermediate electronegativity (1.9–2.2).
== Names == Calcitriol refers specifically to 1,25-dihydroxycholecalciferol. Because cholecalciferol already has one hydroxyl group, only two (1,25) are further specified in this nomenclature, but in fact there are three (1,3,25-triol), as indicated by the name calcitriol. The 1-hydroxy group is in the alpha position, and this may be specified in the name, for instance in the abbreviation 1α,25-(OH)2D3. It is also known as cholecalcitriol to emphasize its derivation from vitamin D3. Calcitriol is, strictly, the 1-hydroxylation product of calcifediol (25-OH vitamin D3), derived from cholecalciferol (vitamin D3), rather than the product of hydroxylations of ergocalciferol (vitamin D2). 1α,25-Dihydroxyergocalciferol (ercalcitriol) should be used for the vitamin D2 product. However, the terminology of 1,25-dihydroxyvitamin D, or 1,25(OH)2D, is often used to refer to both types of active forms of vitamin D. Indeed, both bind to the vitamin D receptor and produce biological effects. In clinical use, the differences are unlikely to have major importance. Calcitriol is marketed as a pharmaceutical for medical use under various brand names including Rocaltrol (Roche), Calcijex (Abbott), Decostriol (Mibe, Jesalis), Vectical (Galderma), and Rolsical (Sun Pharma).
Langer and colleagues have conducted multiple forms of research to promote the idea of the flexibility of aging. Her well known 1979 Counterclockwise Study found that when elderly men were temporarily placed in a setting that recreated their past, their health improved, and they even looked younger. This study was originally published by Oxford University Press and later described in her best seller, Mindfulness. It is the basis of what is now called Reminiscence Therapy. The study was the basis of a British Academy of Film and Television Awards nominated BBC series, The Young Ones. The original study was published in a chapter of a book edited by Langer published by Oxford University Press. In 2018, the counterclockwise study was repeated in Italy, but the results have not been published as of 2024. Langer and colleagues have explored the theory of mind/body in other ways. Other work has shown that rewarding behaviors and following completion of memory tasks improves memory. A study showed that among nursing home patients, simply taking care of a plant improves mental and physical health, as well as life expectancy. By having chambermaids call their everyday activity "exercise" rather than "labor," Langer found that the chambermaids experienced a myriad of health benefits including: "a decrease in their systolic blood pressure, weight, and waist-to-hip ratio."
In Germany, there are different types of Eiskaffee (coffee with ice cream). The most widespread form includes milk and sweeteners, and is served in coffeehouses and in Eisdielen (ice cream parlours). It consists of filtered, hot brewed and cooled coffee with vanilla ice cream and whipped cream on top. In supermarkets, the most common canned version includes flavors such as cappuccino and espresso. This iced coffee is very similar to the canned iced coffee in the UK and in the case of some brands (particularly Nestlé) actually the same product.
Sources: en.wikipedia.org
Macroamylasemia is the presence of macroamylase in the blood. Macroamylase is a complex of the enzyme amylase bound to other proteins forming a larger molecule. Macroamylase is typically composed of immunoglobulin A (IgA, 70%) and less often of immunoglobulin G (IgG, 30%). The association of amylase with some drugs has also been reported.
As early as the late 18th century and early 19th century, the digestion of meat by stomach secretions and the conversion of starch to sugars by plant extracts and saliva were known. However, the mechanism by which this occurred had not been identified. In the 19th century, when studying the fermentation of sugar to alcohol by yeast, Louis Pasteur concluded that this fermentation was catalyzed by a vital force contained within the yeast cells called ferments, which he thought functioned only within living organisms. He wrote that "alcoholic fermentation is an act correlated with the life and organization of the yeast cells, not with the death or putrefaction of the cells." In 1833 Anselme Payen discovered the first enzyme, diastase, and in 1878 German physiologist Wilhelm Kühne (1837–1900) coined the term enzyme, which comes from Greek ενζυμον 'in leaven', to describe this process. The word enzyme was used later to refer to nonliving substances such as pepsin, and the word ferment was used to refer to chemical activity produced by living organisms. In 1897 Eduard Buchner began to study the ability of yeast extracts to ferment sugar despite the absence of living yeast cells. In a series of experiments at the University of Berlin, he found that the sugar was fermented even when there were no living yeast cells in the mixture. He named the enzyme that brought about the fermentation of sucrose zymase. In 1907 he received the Nobel Prize in Chemistry "for his biochemical research and his discovery of cell-free fermentation".
Other culinary gelling agents can be used instead of animal-derived gelatine. These plant-derived substances are more similar to pectin and other gelling plant carbohydrates than to gelatine proteins; their physical properties are slightly different, creating different constraints for the preparation and storage conditions. These other gelling agents may also be preferred for certain traditional cuisines or dietary restrictions. Agar, a product made from red algae, is the traditional gelling agent in many Asian desserts. Agar is a popular gelatine substitute in quick jelly powder mix and prepared dessert gels that can be stored at room temperature. Compared to gelatine, agar preparations require a higher dissolving temperature, but the resulting gels congeal more quickly and remain solid at higher temperatures, 40 °C (104 °F), as opposed to 15 °C (59 °F) for gelatine. Vegans and vegetarians can use agar to replace animal-derived gelatine. Another common seaweed-based gelatine substitute is carrageenan, which has been used as a food additive since ancient times. It was first industrially-produced in the Philippines, which pioneered the cultivation of tropical red seaweed species (primarily Eucheuma and Kappaphycus spp.) from where carrageenan is extracted. The Philippines produces 80% of the world's carrageenan supply. Carrageenan gelatine substitute are traditionally known as gulaman in the Philippines. It is widely used in various traditional desserts and are sold as dried bars or in powder form.
== Contraindications == Hydroxyzine is contraindicated for subcutaneous or intra-articular administration. The administration of hydroxyzine in large amounts by ingestion or intramuscular administration during the onset of pregnancy can cause fetal abnormalities. When administered to pregnant rats, mice, and rabbits, hydroxyzine caused abnormalities such as hypogonadism with doses significantly above that of the human therapeutic range. In humans, a significant dose has not yet been established in studies, and, by default, the US Food and Drug Administration (FDA) has introduced contraindication guidelines regarding hydroxyzine. Use by those at risk for or showing previous signs of hypersensitivity is also contraindicated. Other contraindications include the administration of hydroxyzine alongside depressants and other compounds that affect the central nervous system; if necessary, it should only be administered concomitantly in small doses. If administered in small doses with other substances, as mentioned, then patients should refrain from using dangerous machinery, motor vehicles, or any other practice requiring absolute concentration, under safety laws. Studies have also been conducted which show that long-term prescription of hydroxyzine can lead to tardive dyskinesia after years of use, but effects related to dyskinesia have also anecdotally been reported after periods of 7.5 months, such as continual head rolling, lip licking, and other forms of athetoid movement.
==== Medicaid expansions ==== The law establishes a $50 billion Rural Hospital Fund, up from $25 billion, to support health care providers in rural areas, providing a safety net against Medicaid cuts; and it authorizes CMS to approve new Medicaid HCBS waivers to allow non-nursing-home-eligible persons to participate.
Sources: en.wikipedia.org
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.
Quantification usually compares detector response to a standard curve made from reference standards. The curve may be external, internal, or based on standard addition depending on matrix effects. Results are reported with units and, when required, uncertainty.
Carryover occurs when analyte from a previous injection remains in the system and appears in a later chromatogram. It can come from the injector, column, or tubing. Blank injections and needle washes help detect and reduce it.
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.