reference standard raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2025-08-02 and is reviewed periodically as new material appears.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
| Property | Value | Notes |
|---|---|---|
| Retention time RSD | ≤1% for five replicate injections | Typical criterion; method-specific limits apply. |
| Resolution | ≥1.5 between critical pair | Baseline separation is generally desired. |
| Tailing factor | ≤2.0 | Measures peak symmetry. |
| Theoretical plates | ≥2000 per column | Method-dependent; higher values indicate greater efficiency. |
| Peak area RSD | ≤2% for replicate injections | Reflects autosampler and detector precision. |
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
=== Malaria vaccine === In 2014, GSK applied for regulatory approval for the first malaria vaccine. Malaria is responsible for over 650,000 deaths annually, mainly in Africa. Known as RTS,S, the vaccine was developed as a joint project with the PATH vaccines initiative and the Bill and Melinda Gates Foundation. The company has committed to making the vaccine available in developing countries for five per cent above the cost of production. As of 2013, RTS,S, which uses GSK's proprietary AS01 adjuvant, was being examined in a Phase 3 trial in eight African countries. PATH reported that "[i]n the 12-month period following vaccination, RTS,S conferred approximately 50% protection from clinical Plasmodium falciparum disease in children aged 5-17 months, and approximately 30% protection in children aged 6-12 weeks when administered in conjunction with Expanded Program for Immunization (EPI) vaccines." In 2014, Glaxo said it had spent more than US$350 million and expected to spend an additional US$260 million before seeking regulatory approval.
In mass spectrometry, the molecular mass of a small molecule is usually reported as the monoisotopic mass: that is, the mass of the molecule containing only the most common isotope of each element. This also differs subtly from the molecular mass in that the choice of isotopes is defined and thus is a single specific molecular mass out of the (perhaps many) possibilities. The masses used to compute the monoisotopic molecular mass are found in a table of isotopic masses and are not found in a typical periodic table. The average molecular mass is often used for larger molecules, since molecules with many atoms are often unlikely to be composed exclusively of the most abundant isotope of each element. A theoretical average molecular mass can be calculated using the standard atomic weights found in a typical periodic table. The average molecular mass of a very small sample, however, might differ substantially from this since a single sample average is not the same as the average of many geographically distributed samples.
== Safety == Preliminary studies seem to indicate that lithium orotate is safe if taken at lower dosages; a 6 month alcoholism cessation study led to only minor adverse effects in 8 out of 42 patients. However, the lack of safety studies and the over-the-counter drug status raises concerns. Attention to it was specially raised in medical literature after a case report of an 18 year old woman with mild, acute lithium toxicity after taking an overdose (2.16 grams) of a lithium orotate supplement. She was discharged after treatment. Lithium blood levels 90 minutes after ingestion reached 0.31 mEq/L, and an hour later after treatment, 0.40 mEq/L, levels below the serum toxicity level of 1.5 milliequivalents per liter (mEq/L).
== Athletic tracking and self-tracking uses == Hemoglobin can be tracked noninvasively, to build an individual data set tracking the hemoconcentration and hemodilution effects of daily activities for better understanding of sports performance and training. Athletes are often concerned about endurance and intensity of exercise. The sensor uses light-emitting diodes that emit red and infrared light through the tissue to a light detector, which then sends a signal to a processor to calculate the absorption of light by the hemoglobin protein. This sensor is similar to a pulse oximeter, which consists of a small sensing device that clips to the finger.
Sources: en.wikipedia.org
Zirconium-based MOFs such as UiO-66 are a robust class of MOFs (attributed to strong hexanuclear Zr6 metallic nodes) with increased resistance to heat, solvents, and other harsh conditions, which makes them of interest in terms of mechanical properties. Determinations of shear modulus and pelletization have shown that the UiO-66 MOFs are mechanically robust and have high tolerance for pore collapse when compared to ZIFs and carboxylate MOFs. Although the UiO-66 MOF shows increased stability under pelletization, the UiO-66 MOFs amorphized fairly rapidly under ball milling conditions due to destruction of linker coordinating inorganic nodes.
The building, at the cross sections of those streets that were once called Belascoaín, Carlos III, Fraternidad, and Pocito, is at 508 Avenida de Carlos III (English: Carlos III Avenue). To level the ground beneath the Temple, loads of soil and sand were brought in from each of the Six Provinces of Cuba and many of their major rivers; Camagüey Province, Havana Province, Las Villas Province, Matanzas Province, Oriente Province, and Pinar del Río Province.The building's cornerstone was laid on March 25, 1951, by Grand Master Carlos M. Piñero y del Cueto and the building's architect, Emilio Vasconcelos Frayde. Costs for the construction were made possible by voluntary donations donations from the Grand Lodge and Supreme Council of Cuba, and the Daughters of Acacia. A delegate from the Grand Lodge of Pennsylvania, upon seeing the Temple, wrote: "The cost of the temple was approximately US$4,000,000, and when we realize that there are but 31,700 Masons in Cuba, one can fully realize what a magnificent undertaking was brought to completion." On February 27, 1955, the National Masonic Temple of Cuba was officially inaugurated during the Third Inter-American Conference of Symbolic Freemasonry. At the consecration ceremony, Grand Master Carlos M. Piñeiro del Cueto said: "The consecration of the National Masonic Temple stands as a bulwark in the struggle for the freedom of all peoples and the dignity of mankind." At a height of eleven floors, it was at one time the second-tallest building on the entire island of Cuba.
=== Italy === In Italy, after completing a cycle of 6 years of studies, students get the title of "Medico generico" (generic physician), and are authorized to limited activities, like: teach first aid practices, act as temporary substitute of a primary care physician or issue medical certificates for sports purposes. Later the physicians can complete the studies with a specialization training. Such specialization is required even to practice as family doctor or primary care physician. Resident is translated as: "specializzanda" or "specializzando" according to gender.
Sources: en.wikipedia.org
Rubella vaccine is a vaccine used to prevent rubella. Effectiveness begins about two weeks after a single dose and around 95% of people become immune. Countries with high rates of immunization no longer see cases of rubella or congenital rubella syndrome. When there is a low level of childhood immunization in a population it is possible for rates of congenital rubella to increase as more women make it to child-bearing age without either vaccination or exposure to the disease. Therefore, it is important for more than 80% of people to be vaccinated. By introducing rubella containing vaccines, rubella has been eradicated in 81 nations, as of mid-2020. The World Health Organization (WHO) recommends that the rubella vaccine be included in routine vaccinations. If not all people are immunized then at least women of childbearing age should be immunized. It should not be given to those who are pregnant or those with very poor immune function. While one dose is often all that is required for lifelong protection, often two doses are given. Side effects are generally mild. They may include fever, rash, and pain and redness at the site of injection. Joint pain may be reported at between one and three weeks following vaccination in women. Severe allergies are rare. The rubella vaccine is a live attenuated vaccine. It is available either by itself or in combination with other vaccines. Combinations include with measles (MR vaccine), measles and mumps vaccine (MMR vaccine) and measles, mumps and varicella vaccine (MMRV vaccine). A rubella vaccine was first licensed in 1969.
In order for the acyl-CoA to enter the mitochondrion the carnitine shuttle is used: Acyl-CoA is transferred to the hydroxyl group of carnitine by carnitine palmitoyltransferase I, located on the cytosolic faces of the outer and inner mitochondrial membranes. Acyl-carnitine is shuttled inside by a carnitine-acylcarnitine translocase, as a carnitine is shuttled outside. Acyl-carnitine is converted back to acyl-CoA by carnitine palmitoyltransferase II, located on the interior face of the inner mitochondrial membrane. The liberated carnitine is shuttled back to the cytosol, as an acyl-CoA is shuttled into the mitochondrial matrix. Beta oxidation, in the mitochondrial matrix, then cuts the long carbon chains of the fatty acids (in the form of acyl-CoA molecules) into a series of two-carbon (acetate) units, which, combined with co-enzyme A, form molecules of acetyl CoA, which condense with oxaloacetate to form citrate at the "beginning" of the citric acid cycle. It is convenient to think of this reaction as marking the "starting point" of the cycle, as this is when fuel - acetyl-CoA - is added to the cycle, which will be dissipated as CO2 and H2O with the release of a substantial quantity of energy captured in the form of ATP, during the course of each turn of the cycle and subsequent oxidative phosphorylation.
=== Board game === Main articles: Le Havre (board game) Le Havre is a board game about the development of the town of Le Havre. It was inspired by the games Caylus and Agricola and was developed in December 2007.
The four substrates of this enzyme are precorrin-3A, reduced nicotinamide adenine dinucleotide (NADH), oxygen, and a proton. Its products are precorrin-3B, oxidised NAD+, and water. This enzyme is an iron–sulfur protein acting as an oxidoreductase, with molecular oxygen as oxidant and incorporating one of its atoms. The systematic name of this enzyme class is precorrin-3A,NADH:oxygen oxidoreductase (20-hydroxylating). Other names in common use include precorrin-3X synthase, and CobG. This enzyme is part of the biosynthetic pathway to cobalamin (vitamin B12) in aerobic bacteria.
Sources: en.wikipedia.org
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.
Retention time drift can result from changes in mobile phase composition, column temperature, pump flow, or column age. A gradual shift often points to column degradation. A sudden shift may indicate a leak, mixing error, or incorrect mobile phase.
Retention time alone cannot confirm identity because different compounds may elute at similar times. Coupling HPLC with mass spectrometry or comparing against authenticated standards increases confidence. Confirmation usually requires orthogonal data.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.