Stationary phase raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
Reviewed 2026-06-13. Anything still debated is marked as such rather than presented as settled.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Aesthetic Theory (1970) The Stars Down to Earth and Other Essays on the Irrational in Culture (1975) Beethoven: The Philosophy of Music; Fragments and Texts (1993) The Psychological Technique of Martin Luther Thomas' Radio Addresses (2000) Kant's 'Critique of Pure Reason' (2002) Current of Music (2006) Aspects of the New Right-Wing Extremism (1969 lecture; first published in English, 2020)
Adverse reactions from acupuncture, which are unusual and uncommon in typical acupuncture practice, included syncope, galactorrhoea, bilateral nystagmus, pyoderma gangrenosum, hepatotoxicity, eruptive lichen planus, and spontaneous needle migration. A 2013 systematic review found 31 cases of vascular injuries caused by acupuncture, three causing death. Two died from pericardial tamponade and one was from an aortoduodenal fistula. The same review found vascular injuries were rare, bleeding and pseudoaneurysm were most prevalent. A 2011 systematic review (without restriction in time or language), aiming to summarize all reported case of cardiac tamponade after acupuncture, found 26 cases resulting in 14 deaths, with little doubt about cause in most fatal instances. The same review concluded that cardiac tamponade was a serious, usually fatal, though theoretically avoidable complication following acupuncture, and urged training to minimize risk. A 2012 review found that a number of adverse events were reported after acupuncture in the UK's National Health Service (NHS), 95% of which were not severe, though miscategorization and under-reporting may alter the total figures. From January 2009 to December 2011, 468 safety incidents were recognized within the NHS organizations. The adverse events recorded included retained needles (31%), dizziness (30%), loss of consciousness/unresponsive (19%), falls (4%), bruising or soreness at needle site (2%), pneumothorax (1%) and other adverse side effects (12%).
Giddings also envisioned the capabilities of Supercritical fluid chromatography, by developing the theory and ground work of dense gas chromatographic system. Eventually Prof Giddings invented the one-phase separation technique called "field-flow fractionation" (FFF). He developed the concept of a chromatographic-like system in which retention is established and controlled by an external field rather than by the stationary phase. The FFF system extends the range of chromatography upward to include macromolecules and particles of almost every type and size, from 0.001 to 10 μm and beyond. He was nominated for a Nobel Prize in 1984 and 1994. Giddings received numerous honors for his work including American Chemical Society Awards in Chromatography and Electrophoresis, in Analytical Chemistry, and in Separation Science and Technology. He also received the Tswett Medal in Chromatography, and the Nichols Medical from the New York Section of the ACS. On May 27, 1987, Giddings received an honorary doctorate from the faculty of pharmacy at Uppsala University, Sweden He died of cancer in 1996.
== Clinical significance == Proenkephalin is produced by the medium spiny neurons of the striatum which undergo neurodegeneration in early stages of Huntington's disease (HD). PENK and related peptides measured in cerebrospinal fluid are proposed as potential biomarkers of disease progression in HD. Furthermore, PENK has been found associated with acute kidney injury and glomerular filtration rate in steady-state and critically ill patients.
Sources: en.wikipedia.org
The four substrates of this enzyme are phenol, reduced nicotinamide adenine dinucleotide phosphate (NADPH), oxygen and a proton. Its products are catechol, oxidised NADP+, and water. The enzyme is a flavin-containing monooxygenase that uses molecular oxygen as oxidant and incorporates one of its atoms into the starting material. The systematic name of this enzyme class is phenol,NADPH:oxygen oxidoreductase (2-hydroxylating). Other names in common use include phenol hydroxylase, and phenol o-hydroxylase. It uses flavin adenine dinucleotide as a cofactor. The enzyme from Trichosporon cutaneum can hydroxylate a range of phenols.
== Further reading == Gogarten, J Peter; Elena Hilario (2006). "Inteins, introns, and homing endonucleases: recent revelations about the life cycle of parasitic genetic elements". BMC Evol Biol. 6 (1): 94. doi:10.1186/1471-2148-6-94. ISSN 1471-2148. PMC 1654191. PMID 17101053.
This concept of feed-forward stimulation will likely become more prevalent as physiological markers of targeted diseases and neural disorders are discovered and verified. The on-demand stimulation may may extend the duration of battery life if sensing and signal-processing demands of the system are sufficiently power-efficient. New electrode designs could yield more efficient and precise stimulation, requiring less current and minimizing unwanted side-stimulation. In addition, to overcome the challenge of preventing lead migration in areas of the body that are subject to motion such as turning and bending, researchers are exploring developing small stimulation systems that are recharged wirelessly rather than through an electrical lead.
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.