retention time comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Last reviewed on 2025-12-21. Where a claim depends on a specific study, the study is described rather than over-claimed.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
| Property | Value | Notes |
|---|---|---|
| Retention time RSD | ≤1% for five replicate injections | Typical criterion; method-specific limits apply. |
| Resolution | ≥1.5 between critical pair | Baseline separation is generally desired. |
| Tailing factor | ≤2.0 | Measures peak symmetry. |
| Theoretical plates | ≥2000 per column | Method-dependent; higher values indicate greater efficiency. |
| Peak area RSD | ≤2% for replicate injections | Reflects autosampler and detector precision. |
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
Lipids are the most diverse group of biochemicals. Their main structural uses are as part of internal and external biological membranes such as the cell membrane. Their chemical energy can also be used. Lipids contain a long, non-polar hydrocarbon chain with a small polar region containing oxygen. Lipids are usually defined as hydrophobic or amphipathic biological molecules but will dissolve in organic solvents such as ethanol, benzene or chloroform. The fats are a large group of compounds that contain fatty acids and glycerol; a glycerol molecule attached to three fatty acids by ester linkages is called a triacylglyceride. Several variations of the basic structure exist, including backbones such as sphingosine in sphingomyelin, and hydrophilic groups such as phosphate in phospholipids. Steroids such as sterol are another major class of lipids.
=== Retrospective views === Retrospectively, the album is viewed very positively and is often considered the band's "breakthrough". JR Moores, writing for The Guardian, called it "the most gloriously sardonic collection of caustic-yet-catchy mini-anthems of its era" and bemoaned its lack of popularity upon release. Candice Eley of Treble called it a "masterpiece [...] an album as hardcore and as cheeky as its title might imply." Kyle Fowle of Spectrum Culture considers it to be "a monumental album. It may not be the most revolutionary revision of the punk rock aesthetic or vision, but it’s definitely the most fun. There’s a perfect balance present on the record; Mclusky is focused on creating a foreboding, harsh, loud record, but never once take themselves too seriously. The overdriven guitar solos and Falkous’ shriek hit you like a freight train, but are never alienating or unwanted. There's no overarching political or creative statement, just three guys beating the shit out of their instruments and having a blast doing it.
Dicyanamide (abbreviated as dca when a ligand) is an anion with the formula C2N−3. It contains two cyanide groups bound to a central nitrogen anion. Dicyanamide is formed by decomposition of 2-cyanoguanidine. Dicyanamide is used extensively as a counterion of organic and inorganic salts, as it is a "chemically inert, hydrophobic anion" and pseudohalide. It is also as a reactant for the synthesis of various covalent organic structures. Dicyanamide has a very low proton affinity, less than 310 ± 3 kcal·mol−1. Its gas-phase conjugate acid is iminomethylidenecyanamide HN=C=N−C≡N, which is predicted to be slightly more stable than the symmetric tautomer dicyanimide N≡C−NH−C≡N. Dicyanamide was used as an anionic component in an organic superconductor that was, when reported in 1990, a superconductor with the highest transition temperature in its structural class. Dean Kenyon examined the role of this chemical in reactions that can produce peptides, and a co-worker examined dicyanamide's possible role in primordial biogenesis.
The group called for a thorough investigation of the Lancet article, as well as the immediate release of anonymized individual patient data to an unbiased statistical expert, and suggested the article should be retracted. The Lancet Group recognised the concerns about the validity of data published in the article and invited the authors of the article to respond to these latest questions.
Sources: en.wikipedia.org
In 1990, Brigadier Oupa Gqozo deposed Sebe and ruled as a dictator—despite an initial promise of a swift return to civilian rule. During 1991 and 1992, many of the legal foundations of apartheid in South Africa were removed, undermining the rationale for the homelands' continued existence. The African National Congress pressed strongly for them to be reincorporated into South Africa. This was opposed by Gqozo and the other homeland leaders.
== Discovery == The discovery of hepatalin action was published in 1996 by a team led by W. Wayne Lautt from the University of Manitoba in Winnipeg, Manitoba, Canada. The many roles of the hepatic nerves had been studied for years with Lautt proposing in 1979 that hepatic parasympathetic nerve dysfunction could result in type 2 diabetes. The action of hepatalin was not seen until 1991 when an experiment was conducted to determine if insulin in the blood perfusing the brain could activate the nerves in the liver. It did not, but the response to an injection of a pulse of insulin either to the brain or systemically, was decreased by hepatic surgical denervation. Further studies showed that denervation of the liver reduced the response to insulin in the hindlimbs but had no effect on the liver.
Cns1 is a oxidoreductase/dehydrogenase. Cns2 is a HDc-family metal-dependent phosphohydrolase. There is a binding interaction between Cns1 and Cns2. Cns3 is a bifunctional protein. It has an N-terminal (9–101 aa) nucleoside/nucleotide kinase (NK) domain and a C-terminal (681-851 aa) HisG-family ATP phosphoribosyltransferase domain. Cns4 is an ABC transporter, specifically of the putative pleiotropic drug resistance (PDR) family. To produce cordycepin:
Sources: en.wikipedia.org
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.
Retention time drift can result from changes in mobile phase composition, column temperature, pump flow, or column age. A gradual shift often points to column degradation. A sudden shift may indicate a leak, mixing error, or incorrect mobile phase.
Retention time alone cannot confirm identity because different compounds may elute at similar times. Coupling HPLC with mass spectrometry or comparing against authenticated standards increases confidence. Confirmation usually requires orthogonal data.
System suitability is a set of checks performed before and during an HPLC run to confirm that the instrument and method are working as expected. It may include retention time repeatability, resolution between peaks, peak symmetry, and signal intensity. Failing suitability criteria usually invalidates the run.