The short version of Chromatogram fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-05-15. Anything still debated is marked as such rather than presented as settled.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
=== Legal === This technique is also used for detection of illicit drugs in various samples. The most common method of drug detection has been an immunoassay. This method is much more convenient. However, convenience comes at the cost of specificity and coverage of a wide range of drugs, therefore, HPLC has been used as well as an alternative method. As HPLC is a method of determining (and possibly increasing) purity, using HPLC alone in evaluating concentrations of drugs was somewhat insufficient. Therefore, HPLC in this context is often performed in conjunction with mass spectrometry. Using liquid chromatography-mass spectrometry (LC-MS) instead of gas chromatography-mass spectrometry (GC-MS) circumvents the necessity for derivitizing with acetylating or alkylation agents, which can be a burdensome extra step. LC-MS has been used to detect a variety of agents like doping agents, drug metabolites, glucuronide conjugates, amphetamines, opioids, cocaine, BZDs, ketamine, LSD, cannabis, and pesticides. Performing HPLC in conjunction with mass spectrometry reduces the absolute need for standardizing HPLC experimental runs.
=== Further manifestations of solvent hydrogen bonding === Increase in the melting point, boiling point, solubility, and viscosity of many compounds can be explained by the concept of hydrogen bonding. Negative azeotropy of mixtures of HF and water. The fact that ice is less dense than liquid water is due to a crystal structure stabilized by hydrogen bonds. Dramatically higher boiling points of NH3, H2O, and HF compared to the heavier analogues PH3, H2S, and HCl, where hydrogen-bonding is absent. Viscosity of anhydrous phosphoric acid and of glycerol. Dimer formation in carboxylic acids and hexamer formation in hydrogen fluoride, which occur even in the gas phase, resulting in gross deviations from the ideal gas law. Pentamer formation of water and alcohols in apolar solvents.
Gas chromatography (GC) is a common type of chromatography used in analytical chemistry for separating and analyzing compounds that can be vaporized without decomposition. Typical uses of GC include testing the purity of a particular substance or separating the different components of a mixture. In preparative chromatography, GC can be used to prepare pure compounds from a mixture. Gas chromatography is also sometimes known as vapor-phase chromatography (VPC), or gas–liquid partition chromatography (GLPC). These alternative names, as well as their respective abbreviations, are frequently used in scientific literature. Gas chromatography is the process of separating compounds in a mixture by injecting a gaseous or liquid sample into a mobile phase, typically called the carrier gas, and passing the gas through a stationary phase. The mobile phase is usually an inert gas or an unreactive gas such as helium, argon, nitrogen or hydrogen. The stationary phase can be solid or liquid, although most GC systems today use a polymeric liquid stationary phase. The stationary phase is contained inside of a separation column. Today, most GC columns are fused silica capillaries with an inner diameter of 100–320 micrometres (0.0039–0.0126 in) and a length of 5–60 metres (16–197 ft). The GC column is located inside an oven where the temperature of the gas can be controlled and the effluent coming off the column is monitored by a suitable detector.
In many of these countries, flower farmers could choose a location for year-round plant production based on the altitude, cooler crops higher in the mountains, warmer crops at lower altitudes and offer work and income to the local population. This led to an increase in the taxa used as cut flowers across the world.
=== Use of paper microfluidics in blood grouping === Recently, paper microfluidics was used in the fabrication of numerous immunological tests. Khan et al. in 2010 investigated a blood typing device based on the principle that red blood cell agglutination, triggered by specific antigeninteraction, drastically decreases blood wicking and transport on paper or chromatographic media. The concept was exhibited with a paper-based microfluidic device prototype, made from a filter paper shaped to a central zone with three extending channels. Each channel is treated with a different solution of antibody (Epiclone Anti-A, Anti-B, and Anti-D). Since μPADs were purposely created for use in resource-shortage conditions, it is highly important to provide the capability to analyze real samples like non-pretreated human blood and urine. This device is constructed to analyze whole-blood samples, which is an important step to increase the user acceptance of paper-based microfluidic diagnostics. The analysis is based on the wicking behavior of blood or antibody mixture on paper. Mixing blood samples with immunoglobulin M antibodies, specific for each blood group, causes agglutination of the red blood cells (RBC) by polymer bridging upon adsorption on the corresponding RBC antigens, and chromatographic separation of sample on the certain channel of the device occurs. Simultaneously, separation doesn't happen on hands soaked in non-specific antibody and the blood sample is weakened as a uniform and stable solution.
Sources: en.wikipedia.org
== External links == Opioid+Receptors at the U.S. National Library of Medicine Medical Subject Headings (MeSH) "How opioid drugs activate receptors". National Institute of Health. "Opioid Receptors". IUPHAR Database of Receptors and Ion Channels. International Union of Basic and Clinical Pharmacology. Corbett A, McKnight S, Henderson G. "Opioid Receptors". BLTC Research. Retrieved 2008-03-21. Guzman F. "Video lectures on opioid receptors". Pharmacology Corner. Retrieved 2012-07-30. Lomize A, Lomize M, Pogozheva I. "Orientations of Proteins in Membranes (OPM) database". University of Michigan. Archived from the original on 2014-01-03. Retrieved 2008-03-21.
In a study by Belicka et al., six sediment cores from two shelf-basin transects in the Chukchi and Beaufort Seas of the Arctic Ocean were examined in order to compare the sources and preservation of organic carbon between the two differing depositional regimes. This study found an unexpected correlation between dinosterol and α-amyrin, which is found in terrestrial plants, in shelf and slope sediments, in particular the Beaufort Shelf, suggesting that dinoflagellates contribute significantly to phytoplankton abundance in areas of seasonal open water. Dinosterol was only observed above the permanent ice pack, suggesting that dinoflagellates are restricted to open waters, which in the Arctic occur near the shallow shelves. Consequently, dinosterol may be a potential indicator of the history of open water conditions.
Collin Whitfield Willson. Animal Welfare Veterinary Lead, Food Standards Agency. For services to Animal Welfare and to Veterinary Public Health in the Meat Industry. Christine Mary Windmill. Honorary Vice-President, TennisScotland. For services to Tennis. Rabbi Jonathan Wittenberg. Senior Rabbi, Masorti Judaism. For services to the Jewish Community and to Interfaith Relations. Carl Vivian Woodall. Lately Director of Facilities, House of Lords. For services to Parliament. Ian William James Woodroffe. Founder, easyfundraising. For services to Charitable Fundraising. Philip Graham Wynn. Chair, LEAF (Linking Environment and Farming). For services to Farming and to the Environment. Professor Julia Mary Yeomans FRS. Professor of Physics and Head, Rudolf Peierls Centre, University of Oxford. For services to Physics. Zehra Zaidi. For services to International Development, to Humanitarian Action and to Community Cohesion. Helen Margaret Zammit-Willson. Director, National Valuation Unit, Valuation Office Agency. For services to the Surveying Profession. International list Richard Allan, Director and Chief Executive Officer, The Mentor Initiative. For services to victims of war and natural disasters. Robert Berry, Director, Financial Reporting Authority, Cayman Islands. For services to the UK Sanctions Regime and Global Financial Standards in the Cayman Islands. Dr Ruth Lawson, Development Director and Chargé d'Affaires, British Embassy Khartoum, Sudan. For services to International Development and British Foreign Policy.
Clinical pathology is a medical specialty that is concerned with the diagnosis of disease based on the laboratory analysis of bodily fluids, such as blood, urine, and tissue homogenates or extracts using the tools of chemistry, microbiology, hematology, molecular pathology, and Immunohaematology. This specialty requires a medical residency. Clinical pathology is a term used in the US, UK, Ireland, many Commonwealth countries, Portugal, Brazil, Italy, Japan, and Peru; countries using the equivalent in the home language of "laboratory medicine" include Austria, Germany, Romania, Poland and other Eastern European countries; other terms are "clinical analysis" (Spain) and "clinical/medical biology (France, Belgium, Netherlands, North and West Africa).
Symptoms of overdose include respiratory depression, drowsiness leading to coma and sometimes to death, drooping of skeletal muscles, low heart rate, and decreasing blood pressure. At the hospital, individuals with hydromorphone overdose are provided supportive care, such as assisted ventilation to provide oxygen and gut decontamination using activated charcoal through a nasogastric tube. Opioid antagonists, such as naloxone, also may be administered concurrently with oxygen supplementation. Naloxone works by reversing the effects of hydromorphone, and is administered only in the presence of significant respiratory depression and circulatory depression. Sugar cravings associated with hydromorphone use are the result of a glucose crash after transient hyperglycemia following injection, or a less profound lowering of blood sugar over a period of hours, in common with morphine, heroin, codeine, and other opioids.
Sources: en.wikipedia.org
BMS-986121: μ-PAM BMS-986122: μ-PAM BPRMU191: confers agonistic properties to small-molecule morphinan antagonists Ignavine Oxytocin: μ-PAM δ-PAM (see reference) Cannabidiol Tetrahydrocannabinol Sodium (Na+)
== Clinical significance in humans == Eccentric hypertrophy is a type of hypertrophy in which the walls and chamber of a hollow organ undergo growth, resulting in an overall increase in size and volume. It is most commonly described in the left ventricle of the heart. Sarcomeres are added in series, as for example in dilated cardiomyopathy (in contrast to hypertrophic cardiomyopathy, a type of concentric hypertrophy, where sarcomeres are added in parallel).
A similar resemblance has been noted by Joanna Jurewicz, who argues that the first four nidanas resemble the Hymn of Creation (RigVeda X, 12) and other Vedic sources which describe the creation of the cosmos. Jurewicz argues that dependent origination is "a polemic" against the Vedic creation myth and that, paradoxically, "the Buddha extracted the essence of Vedic cosmogony and expressed in explicit language." Richard Gombrich agrees with this view, and argues that the first four elements of dependent origination are the Buddha's attempt to "ironize and criticize Vedic cosmogony." According to Gombrich, while in the Vedic creation theory "the universe is considered to be grounded on a primordial essence which is endowed with consciousness," the Buddha's theory avoids this essence (atman-Bahman). Jurewicz and Gombrich compare the first nidana, ignorance (avijja), with the stage before creation that is described in the Rigveda's Hymn of Creation. While the term avidya does not actually appear in this Hymn, the pre-creation stage is seen as unknowable and characterized by darkness. According to Gombrich, at this stage "consciousness is non-dual, which is to say that it is the ability to cognize but not yet consciousness of anything, for there is no split yet into subject and object." This is different from the Buddha's point of view, in which consciousness is always consciousness of something. Jurewicz then compares the Vedic creator's desire and hunger to create the atman (or "his second self") with volitional impulses (samskara).
The fifth and final single from the album, "Zzyzx Rd.", started receiving radio airplay in fall 2007; no music video was made for the single. The band began touring in support of the album before its release, starting with several free shows in the US, followed by appearances at festivals in Europe. They then joined Korn for their 2006 edition of Family Values Tour across the US, with 33 dates across 3 months. On August 8, 2006, Stone Sour made a special guest appearance on The Tonight Show with Jay Leno to promote and perform the second single, "Through Glass." They also performed at the Japanese Summer Sonic Festival midway through the Family Values Tour. In November and December 2006, Stone Sour joined Disturbed for their Music as a Weapon Tour. In January 2007, Stone Sour joined Evanescence for a Canadian tour, followed by a headlining tour of Europe. They then headlined the spring 2007 Jägermeister Music Tour across the US, followed by headlining tours in Australia and Japan. They then started a tour in Europe playing at festivals and selected headline shows. They finished touring in support of the album with a headlining tour in the US in August and September in 2007.
Adenylyl cyclase is regulated by G proteins, which can be found in the monomeric form or the heterotrimeric form, consisting of three subunits. Adenylyl cyclase activity is controlled by heterotrimeric G proteins. The inactive or inhibitory form exists when the complex consists of alpha, beta, and gamma subunits, with GDP bound to the alpha subunit. In order to become active, a ligand must bind to the receptor and cause a conformational change. This conformational change causes the alpha subunit to dissociate from the complex and become bound to GTP. This G-alpha-GTP complex then binds to adenylyl cyclase and causes activation and the release of cAMP. Since a good signal requires the help of enzymes, which turn on and off signals quickly, there must also be a mechanism in which adenylyl cyclase deactivates and inhibits cAMP. The deactivation of the active G-alpha-GTP complex is accomplished rapidly by GTP hydrolysis due to the reaction being catalyzed by the intrinsic enzymatic activity of GTPase located in the alpha subunit. It is also regulated by forskolin, as well as other isoform-specific effectors:
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
System suitability is a set of checks performed before and during an HPLC run to confirm that the instrument and method are working as expected. It may include retention time repeatability, resolution between peaks, peak symmetry, and signal intensity. Failing suitability criteria usually invalidates the run.