If you have been reading about Stationary phase and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-12-05. Where a claim depends on a specific study, the study is described rather than over-claimed.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
A flow of argon gas (usually 13 to 18 liters per minute) is introduced between the two outermost tubes of the torch and an electric spark is applied for a short time to introduce free electrons into the gas stream. These electrons interact with the radio-frequency magnetic field of the induction coil and are accelerated first in one direction, then the other, as the field changes at high frequency (usually 27.12 million cycles per second). The accelerated electrons collide with argon atoms, and sometimes a collision causes an argon atom to part with one of its electrons. The released electron is in turn accelerated by the rapidly changing magnetic field. The process continues until the rate of release of new electrons in collisions is balanced by the rate of recombination of electrons with argon ions (atoms that have lost an electron). This produces a ‘fireball’ that consists mostly of argon atoms with a rather small fraction of free electrons and argon ions. The temperature of the plasma is very high, of the order of 10,000 K. The plasma also produces ultraviolet light, so for safety should not be viewed directly. The ICP can be retained in the quartz torch because the flow of gas between the two outermost tubes keeps the plasma away from the walls of the torch. A second flow of argon (around 1 liter per minute) is usually introduced between the central tube and the intermediate tube to keep the plasma away from the end of the central tube. A third flow (again usually around 1 liter per minute) of gas is introduced into the central tube of the torch.
The reproductive system begins development at four to five weeks of gestation with germ cell migration. The bipotential gonad results from the collection of the medioventral region of the urogenital ridge. At the five-week point, the developing gonads break away from the adrenal primordium. Gonadal differentiation begins 42 days following conception.
=== Positron emission tomography === Positron emission tomography (PET) imaging in theranostics provides insight into metabolic and molecular processes within the body. The PET scanner detects photons and creates three-dimensional images that enable visualization and quantification of physiological and biochemical processes. PET imaging uses radiotracers that target specific molecules or processes. For example, [18F] fluorodeoxyglucose (FDG) is commonly used to assess glucose metabolism, as cancer cells exhibit increased glucose uptake. Other radiotracers target specific receptors, enzymes, or transporters, allowing the evaluation of various physiological and pathological processes. PET imaging plays a role in both diagnosis and treatment planning. It aids in the identification and staging of diseases, such as cancer, by visualizing the extent and metabolic activity of tumors. PET scans can also guide treatment decisions by assessing treatment response and monitoring disease progression. Additionally, PET imaging is used to determine the suitability of patients for targeted therapies based on specific molecular characteristics, enabling personalized treatment approaches.
Shortly before the war, Hans von Halban and Lew Kowarski moved their research on neutron moderation from France to Britain, smuggling the entire global supply of heavy water (which had been made in Norway) across in twenty-six steel drums. During World War II, Nazi Germany was known to be conducting experiments using heavy water as moderator for a nuclear reactor design. Such experiments were a source of concern because they might allow them to produce plutonium for an atomic bomb. Ultimately it led to the Allied operation called the "Norwegian heavy water sabotage", the purpose of which was to destroy the Vemork deuterium production/enrichment facility in Norway. At the time this was considered important to the potential progress of the war. After World War II ended, the Allies discovered that Germany was not putting as much serious effort into the program as had been previously thought. The Germans had completed only a small, partly built experimental reactor (which had been hidden away) and had been unable to sustain a chain reaction. By the end of the war, the Germans did not even have a fifth of the amount of heavy water needed to run the reactor, partially due to the Norwegian heavy water sabotage operation. However, even if the Germans had succeeded in getting a reactor operational (as the U.S. did with Chicago Pile-1 in late 1942), they would still have been at least several years away from the development of an atomic bomb.
Sources: en.wikipedia.org
=== Sensor === The hypothalamus senses external stimuli mainly through a number of hormones such as leptin, ghrelin, PYY 3-36, orexin and cholecystokinin; all modify the hypothalamic response. They are produced by the digestive tract and by adipose tissue (leptin). Systemic mediators, such as tumor necrosis factor-alpha (TNFα), interleukins 1 and 6 and corticotropin-releasing hormone (CRH) influence appetite negatively; this mechanism explains why ill people often eat less. Leptin, a hormone secreted exclusively by adipose cells in response to an increase in body fat mass, is an important component in the regulation of long term hunger and food intake. Leptin serves as the brain's indicator of the body's total energy stores. When leptin levels rise in the bloodstream they bind to receptors in ARC. The functions of leptin are to:
IUPAC Nomenclature for Chromatography Overlapping Peaks Program – Learning by Simulations Chromatography Videos – MIT OCW – Digital Lab Techniques Manual Chromatography Equations Calculators – MicroSolv Technology Corporation
=== Polymeric nanoparticles === The mechanism for the transport of polymer-based nanoparticles across the BBB has been characterized as receptor-mediated endocytosis by the brain capillary endothelial cells. Transcytosis then occurs to transport the nanoparticles across the tight junction of endothelial cells and into the brain. Surface coating nanoparticles with surfactants such as polysorbate 80 or poloxamer 188 was shown to increase uptake of the drug into the brain also. This mechanism also relies on certain receptors located on the luminal surface of endothelial cells of the BBB. Ligands coated on the nanoparticle's surface bind to specific receptors to cause a conformational change. Once bound to these receptors, transcytosis can commence, and this involves the formation of vesicles from the plasma membrane pinching off the nanoparticle system after internalization. Additional receptors identified for receptor-mediated endocytosis of nanoparticle delivery systems are the scavenger receptor class B type I (SR-BI), LDL receptor (LRP1), transferrin receptor, and insulin receptor. As long as a receptor exists on the endothelial surface of the BBB, any ligand can be attached to the nanoparticle's surface to functionalize it so that it can bind and undergo endocytosis. Another mechanism is adsorption mediated transcytosis, where electrostatic interactions are involved in mediating nanoparticle crossing of the BBB.
An aqueous environment is essential at all stages of array manufacture and operation to prevent protein denaturation. Therefore, sample buffers contain a high percent of glycerol (to lower the freezing point), and the humidity of the manufacturing environment is carefully regulated. Microwells have the dual advantage of providing an aqueous environment while preventing cross-contamination between samples. In the most common type of protein array, robots place large numbers of proteins or their ligands onto a coated solid support in a pre-defined pattern. This is known as robotic contact printing or robotic spotting. Another fabrication method is ink-jetting, a drop-on-demand, non-contact method of dispersing the protein polymers onto the solid surface in the desired pattern. Piezoelectric spotting is a similar method to ink-jet printing. The printhead moves across the array, and at each spot uses electric stimulation to deliver the protein molecules onto the surface via tiny jets. This is also a non-contact process. Photolithography is a fourth method of arraying the proteins onto the surface. Light is used in association with photomasks, opaque plates with holes or transparencies that allow light to shine through in a defined pattern. A series of chemical treatments then enables deposition of the protein in the desired pattern upon the material underneath the photomask.
It has been indicated that one Mn2+ ion is tightly bound to His370, while the second is loosely bound to Asp276. Human prolidase has four crystal structures, HsProl-Mn, HsProl-Na-GlyPro, HsProl-Mg-LeuPro, and HsProl-Mn-Pro. The first of these structures, HsProl-Mn, pertains to the activity of serum prolidase before binding the substrate. Furthermore, HsProl-Na-GlyPro results from substrate degradation caused by the exchange of the Mn2+ ion with Na+. This is caused by the substrate GlyPro binding to the enzyme. The third crystal structure of serum prolidase is HsProl-Mg-LeuPro. This structure functions similarly to HsProl-Na-GlyPro; however, the substrate utilized in this structure is LeuPro. Additionally, Mn2+ is replaced by Mg2+. These differences cause the structure to be more stable with a lower turnover rate. The final crystal structure of serum prolidase is HsProl-Mn-Pro, which employs Pro as the substrate. This Pro comes from the reaction being catalyzed by this enzyme. The crystal structure of prolidase is well-researched and recorded in the Protein Data Bank.
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.