This is a working overview of Stationary phase, written for readers who want more than a one-paragraph summary but less than a textbook.
This page was last updated on 2026-01-18 and is reviewed periodically as new material appears.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Sorafenib's inhibition of UGT1A9 and UGT1A1 may increase plasma concentration of other drugs. The same goes for the CYP2B6 and CYP2C8 pathways, they are inhibited by sorafenib. Giving sorafenib in combination with rifampicin or inducers of CYP3A4 can decrease plasma concentration of sorafenib. CYP3A4 inhibitors are unlikely to affect sorafenib. Sorafenib is a competitive inhibitor of CYP2C19, CYP2D6 and CYP3A4. It inhibits P-glycoprotein, therefore it can increase the plasma concentration of drugs which are P-glycoprotein substrates. Pazopanib is metabolized in the liver by CYP3A4 enzyme. Strong CYP3A4 inhibitors, other than pazopanib, can increase the plasma concentration of pazopanib, and CYP3A4 inducers will do the opposite. Grapefruit juice is a CYP3A4 inhibitor and should be avoided when taking pazopanib. It is also a weak inhibitor of other liver enzymes, CYP2C8 and CYP2D6. Axitinib is metabolized by CYP3A4 and UGT1A1. Strong inhibitors of CYP3A4 will increase the plasma concentration of axitinib, while weak inhibitors have less effect on the plasma concentration. Strong inducers of CYP3A4 will decrease the plasma concentration of axitinib and should be avoided.
Denmark has changed its energy consumption from 99% fossil fuels (92% oil (all imported) and 7% coal) and 1% biofuels in 1972 to 73% fossil fuels (37% oil (all domestic), 18% coal, 18% natural gas (all domestic)), and 27% renewables (largely biofuels) in 2015. The goal is a full independence of fossil fuels by 2050. This drastic change was initially inspired largely by the discovery of Danish oil and gas reserves in the North Sea in 1972 and the 1973 oil crisis. The course took a giant leap forward in 1984, when the Danish North Sea oil and gas fields, developed by native industry in close cooperation with the state, started major production. In 1997, Denmark became self-sufficient with energy, and the overall CO2 emission from the energy sector began to fall by 1996. Wind energy contribution to the total energy consumption has risen from 1% in 1997 to 5% in 2015. Since 2000, Denmark has increased gross domestic product (GDP) and at the same time decreased energy consumption. Since 1972, the overall energy consumption has dropped by 6%, even though the GDP has doubled in the same period. Denmark had the 6th best energy security in the world in 2014. Denmark has had relatively high energy taxation to encourage careful use of energy since the oil crises in the 1970s, and Danish industry has adapted to this and gained a competitive edge. The so-called "green taxes" have been broadly criticised partly for being higher than in other countries, but also for being more of a tool for gathering government revenue than a method of promoting "greener" behaviour.
The retention factor of the compound of interest should be around 0.2 - 0.3 in order to minimize the time and the amount of eluent to run the chromatography. The other compounds should have retention factors quite different from that of the compount of interest. To pick a good eluent, one run multiple small scale pretests, often using thin layer chromatography (TLC) with the same stationary phase, using solvents of different polarity, until a suitable solvent system is found. Common mobile phase solvents, in order of increasing polarity, include hexane, dichloromethane, ethyl acetate, acetone, and methanol. A common solvent system is hexane:ethyl acetate mixture. The proportions are adjusted so that the target compound has a retention factor of 0.2 - 0.3. Contrary to common misconception, methanol alone can be used as an eluent for highly polar compounds, and does not dissolve silica gel. The eluent flow rate can be optimized. A higher flow rate eluent decreases the time required to run a column and thereby decreases diffusion, improving the resolving power. However, if the flow rate is too high, the analyte would fail to equilibrate between the stationary phase and mobile phase (see Van Deemter's equation). To increase the flow rate of a gravity-flow column chromatography, one can increase the height of the fresh eluent column above the top of the stationary phase, or decrease the tap controls. It can also be increased by using a pump or by using compressed gas (e.g. air, nitrogen, or argon) to push the solvent through the column (flash column chromatography).
=== Nanoemulsions === Another form for nanoparticle delivery systems is oil-in-water emulsions done on a nano-scale. This process uses common biocompatible oils such as triglycerides and fatty acids, and combines them with water and surface-coating surfactants. Oils rich in omega-3 fatty acids especially contain important factors that aid in penetrating the tight junctions of the BBB.
Sources: en.wikipedia.org
=== Dementia === While antipsychotic medications such as risperidone have a slight benefit in people with dementia, they have been linked to a higher incidence of death and stroke. Because of this increased risk of death, treatment of dementia-related psychosis with risperidone is not FDA-approved and carries a black box warning. However, many other jurisdictions regularly use it to control severe aggression and psychosis in those with dementia when other non-pharmacological interventions have failed and their pharmaceutical regulators have approved its use in this population.
22 December A network model analysis suggests that temporary overshoots of climate change – increasing global temperature beyond Paris Agreement goals temporarily as often projected – can increase risks of climate tipping cascades "by up to 72%". In a paywalled article, scientists provide 3D imaging and model analysis to reveal main causes, mechanics, and potential mitigations of the problematic prevalent lithium-ion battery degradation over charge cycles. 26 December – Bio- and electrical engineers prove for the first time that human cerebral organoids transplanted into mice (see 17 Aug 21 and 12 Oct) functionally integrate with their visual cortex. 27 December – Scientists report that a species of Halteria, a single-celled protozoan, is the first known organism for which "a virus-only diet ... is enough to fuel the physiological growth and even population growth".
C-4 (explosive), a high explosive solid C4, butyl-type hydrocarbon chain, a type of four-carbon molecule, especially in C4 reversed-phase chromatography columns Cluster 4, an ESA satellite that studies the Earth's magnetosphere over the course of an entire solar cycle C-4 Protective Mask, standard issue gas mask of the Canadian Armed Forces
Proton donors and acceptors, i.e. acids and base may donate and accept protons in order to stabilize developing charges in the transition state. This is related to the overall principle of catalysis, that of reducing energy barriers, since in general transition states are high energy states, and by stabilizing them this high energy is reduced, lowering the barrier. A key feature of enzyme catalysis over many non-biological catalysis, is that both acid and base catalysis can be combined in the same reaction. In many abiotic systems, acids (large [H+]) or bases ( large concentration H+ sinks, or species with electron pairs) can increase the rate of the reaction; but of course the environment can only have one overall pH (measure of acidity or basicity (alkalinity)). However, since enzymes are large molecules, they can position both acid groups and basic groups in their active site to interact with their substrates, and employ both modes independent of the bulk pH. Often general acid or base catalysis is employed to activate nucleophile and/or electrophile groups, or to stabilize leaving groups. Many amino acids with acidic or basic groups are this employed in the active site, such as the glutamic and aspartic acid, histidine, cystine, tyrosine, lysine and arginine, as well as serine and threonine. In addition, the peptide backbone, with carbonyl and amide N groups is often employed. Cystine and Histidine are very commonly involved, since they both have a pKa close to neutral pH and can therefore both accept and donate protons.
Brominated flame retardants represent a commodity of growing importance, and make up the largest commercial use of bromine. When the brominated material burns, the flame retardant produces hydrobromic acid which interferes in the radical chain reaction of the oxidation reaction of the fire. The mechanism is that the highly reactive hydrogen radicals, oxygen radicals, and hydroxyl radicals react with hydrobromic acid to form less reactive bromine radicals (i.e., free bromine atoms). Bromine atoms may also react directly with other radicals to help terminate the free radical chain-reactions that characterise combustion. To make brominated polymers and plastics, bromine-containing compounds can be incorporated into the polymer during polymerisation. One method is to include a relatively small amount of brominated monomer during the polymerisation process. For example, vinyl bromide can be used in the production of polyethylene, polyvinyl chloride or polypropylene. Specific highly brominated molecules can also be added that participate in the polymerisation process. For example, tetrabromobisphenol A can be added to polyesters or epoxy resins, where it becomes part of the polymer. Epoxies used in printed circuit boards are normally made from such flame retardant resins, indicated by the FR in the abbreviation of the products (FR-4 and FR-2). In some cases, the bromine-containing compound may be added after polymerisation. For example, decabromodiphenyl ether can be added to the final polymers.
Sources: en.wikipedia.org
==== Covalent bonding ==== The enzyme is bound covalently to an insoluble support (such as silica gel or macroporous polymer beads with epoxide groups). This approach provides the strongest enzyme/support interaction, and so the lowest protein leakage during catalysis. The activity of the enzyme being covalently bound is dependent on several factors including: shape, and size of carrier material, coupling method type, the composition and coupling special conditions of carrier material. Affinity-tag binding: is an immobilization method combining physical, and chemical methods where enzymes may be immobilized to a surface, e.g. in a porous material, using non-covalent or covalent Protein tags. This technology has been established for protein purification purposes. This technique is the generally applicable, and can be performed without prior enzyme purification with a pure preparation as the result. Porous glass and derivatives thereof are used, where the porous surface can be adapted in terms of hydrophobicity to suit the enzyme in question.
SELDI can be seen as a combination of solid-phase chromatography and TOF-MS. The sample is applied to a modified chip surface, which allows for the specific binding of proteins from the sample to the surface. Contaminants and unbound proteins are then washed away. After washing the sample, an energy absorbing matrix, such as sinapinic acid (SPA) or α-Cyano-4-hydroxycinnamic acid (CHCA), is applied to the surface and allowed to crystallize with the sample. Alternatively, the matrix can be attached to the sample surface by covalent modification or adsorption before the sample is applied. The sample is then irradiated by a pulsed laser, causing ablation and desorption of the sample and matrix.
=== Structural motifs === In addition to linear degrons, the E3 ligase can in some cases also recognize structural motifs on the substrate. In this case, the 3D motif can allow the substrate to directly relate its biochemical function to ubiquitination. This relation can be demonstrated with TRF1 protein (regulator of human telomere length), which is recognized by its corresponding E3 ligase (FBXO4) via an intermolecular beta sheet interaction. TRF1 cannot be ubiquinated while telomere bound, likely because the same TRF1 domain that binds to its E3 ligase also binds to telomeres.
Bush took office during an economic recession in the wake of the bursting of the dot-com bubble. The September 11 terrorist attacks also impacted the economy. His administration increased federal government spending from $1.8 trillion to $3 trillion (66%), while revenues increased from $2 trillion to $2.5 trillion (from 2000 to 2008). Individual income tax revenues increased by 14%, corporate tax revenues by 50%, and customs and duties by 40%. Discretionary defense spending was increased by 107%, discretionary domestic spending by 62%, Medicare spending by 131%, social security by 51%, and income security spending by 130%. Cyclically adjusted, revenues rose by 35% and spending by 65%. The increase in spending was more than under any predecessor since Lyndon B. Johnson. The number of economic regulation governmental workers increased by 91,196. The surplus in 2000 was $237 billion – the third consecutive surplus and the largest surplus ever. In 2001, Bush's budget estimated that there would be a $5.6 trillion surplus over the next ten years. Facing congressional opposition, Bush held town hall-style meetings across the U.S. to increase public support for his plan for a $1.35 trillion tax cut program, one of the largest tax cuts in history. Bush argued that unspent government funds should be returned to taxpayers, saying "the surplus is not the government's money. The surplus is the people's money." Federal Reserve chairman Alan Greenspan warned of a recession and Bush stated that a tax cut would stimulate the economy and create jobs. Treasury Secretary Paul H.
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.